Product Overview
**Fixed shipping cost is to a commercial address. Residential address, and Lift-Gate service will incur additional charges.**
A 
product.
product.- Applies foaming product to vehicle underbody
- Works with trucks and passenger vehicles
- Vehicle ground clearance: 7-49 in. (17.8-124.5 cm)
- Vehicle weight: up to 40,000 lbs (18.14 metric tons) per axle
- Sensor-operated system starts when vehicles approach - no need for an attendant
- Foam provides long contact times for maximum chemical effectiveness, and a visual way to verify coverage
- Easy to install
- Draws from concentrated product (includes proportioning tank)
- Dilutes at ratios of 4:1 to 530:1 (water:chemical)
- Powered by compressed air and electricity
- Low-pressure system
- Includes water separator to protect pumps
| COMPRESSED AIR REQUIREMENTS | 50 psi (3.4 bar) with 20 cfm (566.3 l/min) |
|---|---|
| WATER REQUIREMENTS | 25-100 psi (1.7-6.9 bar) Backflow prevention is required – consult local plumbing ordinances for more information. |
| LIQUID TEMPERATURE RANGE | 40-100ËšF (4.4-37ËšC) |
| ELECTRICAL REQUIREMENTS | 120 VAC at 60 Hz, 2 amps (GFCI protected outlet) |
| OPERATING VOLTAGE | 120 VAC |
| CHEMICAL COMPATIBILITY | Chemical products used with this equipment must be formulated for this type of application and compatible with unit materials and pump seals. For more information on chemical compatibility, consult the manufacturer or SDS for your product or contact our customer service department |
| POWER TYPE | Compressed air and electricity |
|---|---|
| CHEMICAL PICKUP TYPE | Draws from concentrated product (includes proportioning tank) |
| DILUTION RATIO RANGE (WATER:CHEMICAL) | 4:1 to 530:1 NOTE: Approximate dilutions at 40 psi (2.6 bar) water pressure for water-thin products at 1.0 cP. |
| NUMBER OF PRODUCTS UNIT CAN DRAW FROM | One product |
| SUCTION LINE LENGTH/DIAMETER | From proportioning tank to chemical source: one suction line, 9 ft. (2.7 m) of clear hose with 1/2 in. (12.7 mm) inside diameter From pump box to proportioning tank: six suction lines, each 10 ft. (3.1 m) of blue hose with 3/8 in. (9.5 mm) inside diameter |
| CAPACITY | Proportioning tank: 55 gallons (208.2 liters) |
| FLOW RATE | 13 gal/min (49.2 l/min) NOTE: Flow rate based on chemical with viscosity of water and factory air settings. |
| PUMP SEALS | Santoprene, Viton, or Kalrez |
| NUMBER OF NOZZLES | Includes five ramp nozzle assemblies and two side nozzle assemblies |
| DISTANCE FROM NOZZLES TO CONTROL PANEL | Minimum: 30 ft. (9.1 m) Maximum: approximately 50 ft. (15.2 m) |
| TUBING/FITTING SIZES | Designed for use with 1/2 in. (12.7 mm) inside diameter hose between control panel and nozzles |
| VEHICLE GROUND CLEARANCE | 7-49 in. (17.8-124.5 cm) |
| COVERAGE AREA | With 7 in. (17.8 cm) vehicle ground clearance, coverage area will be up to 65 in. (165.1 cm) wide. With 49 in. (124.5 cm) vehicle ground clearance, coverage area will be up to 102 in. (259.1 cm) wide. |
| VEHICLE WEIGHT | Up to 40,000 pounds (18.14 metric tons) per axle |
| RAMP WIDTH | 12 ft. (3.6 m) |
| TRAFFIC FLOW DIRECTION | Suitable for traffic moving in one or both directions |
| SENSOR TYPE | Detects moving iron-based metal |
